PCIe gen3 Mid-bus Probe

• Supports Gen 1, Gen 2, and Gen 3 PCI Express probing.
•  x1 to x16 unidirectional
•  x1 to x8 bidirectional
•  27” full cable length.
•  12.5” length on low-profile portion
•  0.68” Mated height
•  1 year limited warranty

Mid-bus probing for gen2 PCIe lanes

•  Supports Gen 1 and Gen 2 PCI Express probing.
•  x1 to x16 unidirectional
•  x1 to x8 bidirectional
•  27” full cable length.
•  12.5” length on low-profile portion
•  0.68” Mated height
•  1 year limited warranty

QP-SIB426, 626 or 926 - Signal Integrity Board with 4, 6 or 9 pin connector

Astek Corporation's Interconnect Tester (QP-ICT) provides the ability to test one (1) to five (5) IEEE-1394b interconnects simultaneously. It is ideal for cable and interconnect/backplane testing.

QP-SIGKit-SSIB consists of the following components. Each component may also be purchased individually.

• Option -a -- consists of the following: QP-SSIB Control board, QP-SIA, QP-SSIB-TF-4, QP-SSIB-6-TF, QP-SMA24, QP-SMA26 and QP-DVM
• Option -b -- consists of the following: Everything in option -a plus QP-SSIB-9-TF and QP-SMA29

QP-SIA and associated SSIB Controller provides facilities to test Data/Strobe signaling using an automated process.

Termination and Common Mode Load test fixture

Astek Corporation's Signal Quality Tester (QP-SQT) provides both a Beta trasmit and receive tester in one tool. QP-SQT references both SAE and 1394 Trade Association test documents for 1394b short haul copper characterization testing.

The A9-UHS2-03 Device Test Fixture enables designers to verify compliance of UHS-II card components and devices to the SD Card Association UHS-II PHY Test Specification.

The A9-UHS2 Test Fixtures enable designers to verify compliance UHS-II host systems and UHS-II card components to the SD Card Association UHS-II PHY Test Specification.

The A9-UHS2-01 Host Test Fixture enables designers to verify compliance of UHS-II host systems to the SD Card Association UHS-II PHY Test Specification.

   The Astek A51606 is a 1U wide,16-port SAS switch. The switch extends the capabilities of SAS in direct-attached storage (DAS) environments by allowing multiple servers to connect to one or more independent storage systems.

36 port, Gen2 6Gbps Serial Attached SCSI (SAS) Expander modular add-in-card for system builders.

With 36 lanes of Gen2 6Gbps SAS, system designers can connect hundreds of target disks to a SAS HBA. The A33606-AIC family offers two standard connector configurations to fit your chassis.  The AIC-01 (right) provides 'vertical' IPASS mini-SAS x4 connectors, and the AIC-02 (below) provides 'right-angle' IPASS mini-SAS x4 connectors where vertical space is limited.

 A complete, pre-programmed, Gen2 6Gbps SAS Expander in a PCI/PCI-Express card form factor. For designers looking to add SAS fanout to a design, the Astek A33606-PCI card jump-starts the design cycle by delivering a complete SAS expander subsystem.

A complete, pre-programmed, Gen2 6Gbps SAS Expander in a small mezzanine card form factor. For designers looking to add SAS fanout to a design, the Astek A33606-MMC card jump-starts the design cycle by delvering a complete SAS expander subsystem.

  The Astek A54812 is a 1U high, 12-port (48-lanes) 12Gb/s SAS switch configured with 12 x4 wide-port each capable of 48Gb/s . The switch extends the capabilities of SAS in direct-attached storage (DAS) environments by allowing multiple servers to connect to one or more independent storage systems.

  The Astek A54812 is a 1U high, 12-port (48-lanes) 12Gb/s SAS switch configured with 12 x4 wide-port each capable of 48Gb/s . The switch extends the capabilities of SAS in direct-attached storage (DAS) environments by allowing multiple servers to connect to one or more independent storage systems.

CompactFlash for Embedded Systems